This shows you the differences between two versions of the page.
Next revision | Previous revision Next revision Both sides next revision | ||
c50xx_series [02/05/2014 11:54] Jan De Ceuster File build by odt2dw plugin from fileMAN_C50xx.odt |
c50xx_series [10/06/2014 21:12] Consort [C50xx Series] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ~~TOC: |
- | <sub>{{MAN_C50xx.odt|Original file}}</ | + | ====== |
+ | | **{{pictures/ | ||
- | |Consort\\ **MANUAL**\\ **HANDLEIDING**\\ **MODE D’EMPLOI**\\ **ANLEITUNG**|| | + | | {{pictures/ |
- | | | **{{c50xx_series_Image_0.jpg?154}}**| | + | | {{pictures/ |
- | |**C5010**\\ **C5020**\\ **C5030**\\ **December 2012**| | + | ---- |
- | | {{c50xx_series_Image_1.jpg? | + | =====Installation of the instrument===== |
- | | {{c50xx_series_Image_2.jpg? | + | |
- | Keyboard | + | ===Keyboard=== |
- | **MODE**=Selects all modes or escapes from error traps, calibration procedures, etc. by returning to the original mode. | + | **MODE**=Selects all modes or escapes from error traps, calibration procedures, etc. by returning to the original mode.\\ |
+ | **CAL**=Starts or proceeds a calibration or a function.\\ | ||
+ | **↑↓**=Button for entering a value or for selecting a function.\\ | ||
+ | **ON/ | ||
- | **CAL**=Starts or proceeds a calibration or a function. | + | ===Inputs=== |
- | + | ||
- | éê=Button for entering a value or for selecting a function. | + | |
- | + | ||
- | **ON/OFF**=Switches the instrument on or off. | + | |
- | + | ||
- | Installation of the instrument | + | |
- | + | ||
- | Inputs | + | |
The measuring electrodes should be connected to the corresponding coaxial pH/mV or EC/O2 (C5030: mV2) connectors. Automatic temperature compensation and temperature measurements are possible by plugging a Pt1000 temperature probe into the °C terminals. Without Pt1000, the manual temperature compensation is automatically switched on. | The measuring electrodes should be connected to the corresponding coaxial pH/mV or EC/O2 (C5030: mV2) connectors. Automatic temperature compensation and temperature measurements are possible by plugging a Pt1000 temperature probe into the °C terminals. Without Pt1000, the manual temperature compensation is automatically switched on. | ||
Line 31: | Line 26: | ||
•The instrument will refuse automatic calibration when the electrode is unstable. Insufficient stirring or a worn electrode may be the cause. | •The instrument will refuse automatic calibration when the electrode is unstable. Insufficient stirring or a worn electrode may be the cause. | ||
+ | ---- | ||
+ | =====Device Menu===== | ||
+ | Press **MODE** to go to the menu. Press **CAL** to enter the selected item. Press **MODE** to go back or cancel. | ||
+ | *[pH] | ||
+ | *[mV] | ||
+ | *[mS/cm] (C5010/ | ||
+ | *[SAL] (C5020 only) | ||
+ | *[TDS] (C5020 only) | ||
+ | *[O2] (C5010/ | ||
+ | *[%O2] (C5010/ | ||
+ | * [SETTINGS] | ||
+ | * [LANGUAGE] --> select the desired language and press **OK** | ||
+ | * [CONTRAST] --> | ||
+ | * [ERASE MEMORY] (C5020/ | ||
- | Set-up | + | ---- |
- | + | =====pH measurement===== | |
- | | + | |
- | | + | |
- | pH/ | + | |
- | + | ||
- | pH measurement | + | |
- Select the desired mode (pH) by pressing **MODE. **The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | - Select the desired mode (pH) by pressing **MODE. **The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | ||
- | - The instrument permits to choose between the buffers in memory (1.68, 2.00, 4.00, 4.01, 6.87, 7.00, 9.18, 9.21, 10.01, 12.00, 12.45). Select the proper values and press **CAL**.The unused buffers should be switched off. | + | - The instrument permits to choose between the buffers in memory (1.68, 2.00, 4.00, 4.01, 6.87, 7.00, 9.18, 9.21, 10.01, 12.00, 12.45). Select the proper values and press **CAL**.The unused buffers should be switched off by selecting --.--. |
- Rinse the electrodes with distilled water and immerse them in the first buffer solution. Select [CALIBRATE], | - Rinse the electrodes with distilled water and immerse them in the first buffer solution. Select [CALIBRATE], | ||
- After rinsing the electrodes with distilled water, immerse them in the samples and read the display. | - After rinsing the electrodes with distilled water, immerse them in the samples and read the display. | ||
- Rinse the electrodes always with distilled water after use and store them in a 3...4 M KCl solution. | - Rinse the electrodes always with distilled water after use and store them in a 3...4 M KCl solution. | ||
- | mV measurement | + | |
+ | ---- | ||
+ | =====mV measurement===== | ||
- Select the desired mode (mV) by pressing **MODE. **The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | - Select the desired mode (mV) by pressing **MODE. **The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | ||
- Immerse the electrodes in a standard solution of known potential. Select [CALIBRATE] and press **CAL**. Adjust to the proper value and press **CAL**. | - Immerse the electrodes in a standard solution of known potential. Select [CALIBRATE] and press **CAL**. Adjust to the proper value and press **CAL**. | ||
- | //•Select [RESET] and press ////**CAL **////to reset the calibration.// | + | * //Select [RESET] and press ////**CAL **////to reset the calibration.// |
- | Temperature measurement | + | ---- |
+ | =====Temperature measurement===== | ||
- Select the desired mode (°C) by pressing **MODE**. Should you want to recalibrate, | - Select the desired mode (°C) by pressing **MODE**. Should you want to recalibrate, | ||
- Immerse the Pt1000 in a solution of known temperature. Select [CALIBRATE] and press **CAL**. Adjust to the proper value and press **CAL**. | - Immerse the Pt1000 in a solution of known temperature. Select [CALIBRATE] and press **CAL**. Adjust to the proper value and press **CAL**. | ||
- | //•Select [RESET] and press ////**CAL **////to reset the calibration.// | + | * //Select [RESET] and press ////**CAL **////to reset the calibration.// |
+ | * Without Pt1000, press **CAL**, adjust the manual temperature compensation and proceed by pressing **CAL**. | ||
- | •Without Pt1000, press **CAL**, adjust the manual temperature compensation and proceed by pressing **CAL**. | + | ---- |
- | + | =====rH2 measurement (C5030 only)===== | |
- | rH2 measurement// (C5030 only)// | + | |
- Select [rH2] by pressing **MODE**. | - Select [rH2] by pressing **MODE**. | ||
- After rinsing the pH and redox electrodes with distilled water, immerse them in the samples and read the display. | - After rinsing the pH and redox electrodes with distilled water, immerse them in the samples and read the display. | ||
- | Conductivity/ | ||
- | Conductivity measurement// (C5010, C5020 only)// | + | ---- |
+ | =====Conductivity measurement (C5010, C5020 only)====== | ||
- Select the desired mode (S/cm) by pressing **MODE**. The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | - Select the desired mode (S/cm) by pressing **MODE**. The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | ||
Line 72: | Line 78: | ||
- Rinse the electrode several times with the sample, immerse it in that solution and read the display. | - Rinse the electrode several times with the sample, immerse it in that solution and read the display. | ||
- Rinse the electrode always after use and store it in distilled water (add some detergent to keep the spongy platinum surface in perfect condition). | - Rinse the electrode always after use and store it in distilled water (add some detergent to keep the spongy platinum surface in perfect condition). | ||
- | **TDS measurement**// (C5020 only)// | + | |
+ | ---- | ||
+ | =====TDS measurement (C5020 only)===== | ||
- Select the desired mode (mg/l)(TDS) by pressing **MODE**. The display will immediately show the measured value. | - Select the desired mode (mg/l)(TDS) by pressing **MODE**. The display will immediately show the measured value. | ||
- | Salinity measurement// | ||
+ | ---- | ||
+ | =====Salinity measurement (C5020 only)===== | ||
- Select the desired mode (SAL) by pressing **MODE**. The display will immediately show the measured value. | - Select the desired mode (SAL) by pressing **MODE**. The display will immediately show the measured value. | ||
- | Dissolved oxygen measurement | ||
- | **Dissolved oxygen measurement**//(C5010, C5020 only)// | + | ---- |
+ | =====Dissolved oxygen measurement (C5010, C5020 only)===== | ||
- Select [O2] by pressing **MODE**. The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | - Select [O2] by pressing **MODE**. The display will immediately show the measured value according to the previous calibration. Should you want to recalibrate, | ||
Line 87: | Line 96: | ||
- After rinsing the electrodes with distilled water, immerse them in the samples and read the display. Stirring the solution during the measurements promotes the homogeneity and is **obligatory**! The advection rate must be at least 10 cm/s. | - After rinsing the electrodes with distilled water, immerse them in the samples and read the display. Stirring the solution during the measurements promotes the homogeneity and is **obligatory**! The advection rate must be at least 10 cm/s. | ||
- Rinse the electrode always after use and store it in distilled water. | - Rinse the electrode always after use and store it in distilled water. | ||
- | Interferences | ||
- | |||
- | All substances which can diffuse through the membrane and for which 800 mV potential suffices for polarographic reduction, will be reduced in the electrode. This will give a corresponding current contribution, | ||
- | Good Laboratory Practice | + | ---- |
+ | =====Good Laboratory Practice===== | ||
- Select the desired range by pressing **MODE**. | - Select the desired range by pressing **MODE**. | ||
- Press **CAL**, select GLP and press **CAL** to display a complete calibration report. | - Press **CAL**, select GLP and press **CAL** to display a complete calibration report. | ||
- | Data Storage in the internal memory | ||
- | **Storing data**//(C5020, C5030 only)// | + | ---- |
+ | =====Data logging | ||
+ | ===Storing data=== | ||
- | - Press ê to store the displayed value in memory. The display shows a next storage address. | + | - Press **↓** |
- Select the desired address and press **CAL** to enter the measured value in memory. | - Select the desired address and press **CAL** to enter the measured value in memory. | ||
- | Recalling data// | ||
- | | + | ===Recalling data=== |
+ | | ||
- Select the desired address to read the stored values. | - Select the desired address to read the stored values. | ||
- Press **MODE** to return to the normal measurements. | - Press **MODE** to return to the normal measurements. | ||